i m a g e r e j e c t i o n m i x e r p r o d u c t s 100 davids drive, hauppauge, ny 11788 ? tel: (631) 436--400 ??fax: (631) 436-7430 ? www.miteq.com models: arl5359lc2a, arl5359lc2b and ARL5359LC2C features ? rf/lo frequency............... 5.3 to 5.9 ghz ? conversion gain ............... 33 db typical ? noise figure....................... 3 db typical ? limiter protection ............. 1 watt cw, 50 watts peak 5.3 to 5.9 ghz low-noise receiver front ends miteqs model ar series offers state-of-the-art low-noise amplifiers integrated with our ultra-small image rejec- tion mixers to provide a complete receiver front-end assembly . this device comes in a nonhermetic housing, how - ever a hermetically-sealed housing is available for extreme environmental conditions. electrical specifications input parameters condition units min. typ. max. rf frequency range ghz 5.3 5.9 rf vswr (rf = -30 dbm) ratio 2.5:1 maximum input power cw watts 1 peak watts 50 lo frequency range ghz 5.3 5.9 lo power range dbm +10 +13 lo vswr ratio 2.5:1 bias +15 volts ma 150 transfer characteristics condition units min. typ. max. conversion gain (note 1) dbm 30 33 db single-sideband noise figure at 25 db 3 3.5 image rejection (note 1) db 18 lo-to-rf isolation db 40 lo-to-if isolation db 25 output power at 1 db compression dbm +6 input two-tone third-order intercept point dbm +16 output parameters condition units min. typ. max. if frequency mhz 20 40 mhz 40 80 mhz 100 200 if vswr (if = -10 dbm) ratio 2:1
i m a g e r e j e c t i o n m i x e r p r o d u c t s 100 davids drive, hauppauge, ny 11788 ? tel: (631) 436--400 ??fax: (631) 436-7430 ? www.miteq.com arl5359lc2a typical test data maximum ratings specification temperature .................. +25c operating temperature ........................ -54 to +85 storage temperature .......................... -65 to +125 outline drawing general note 1. unit aligned for rf > lo conversion. note: all dimensions shown in brackets [ ] are in millimeters. note: test data supplied at 25; conversion gain, lo--o--f isolation, image rejection and noise figure. rf frequency (mhz) c o n v e r s i o n g a i n ( d b ) conversion gain - lower sideband (lsb rejected lo = +10 dbm rf = -30 dbm if = 30 mhz) l o - t o - r f i s o l a t i o n ( d b ) lo-to-rf isolation lo frequency (mhz) image rejection i m a g e r e j e c t i o n ( d b ) rf frequency (mhz) 50 45 4 0 3530 2 5 20 15 10 50 5300 min. 5350 5400 5450 5500 5550 5600 5650 5700 5750 5800 5850 5300 5350 5400 5450 5500 5550 5600 5650 5700 5750 5800 5850 5.3 5.54 5.66 5.78 5.9 5.42 noise figure vs. lo frequency frequency (ghz) 10 86 4 2 0 n o i s e f i g u r e ( d b ) 50 45 4035 30 25 20 15 10 50 5300 min. 5350 5400 5450 5500 5550 5600 5650 5700 5750 5800 5850 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 min. n o i s e f i g u r e ( d b ) .250 [6.35] .075 [1.905] 1.850 [46.99] .500 [12.70] .100 [2.54] dia (2 holes) 2.0 [50.80] .50 [12.70] conn. rf sma (female) (3 places) lo in if out rf in +15v 1.0 [25.40] .750 [19.05] .250 [6.35] .250 [6.35] .03 [.762] dia x .25 [6.35] lg. .450 [11.43] .950 [ 24.13] 1.142 [29]
|
